Quickshift speed sensor (Twingo, Clio, Modus): symptoms, codes and replacement

Quickshift speed sensor (Twingo, Clio, Modus): symptoms, codes and replacement

Does your Quickshift lose automatic mode while driving, drop back into neutral or manual mode, and does the speedometer fall to 0? Before suspecting the robot, check the speed sensor. It is a small, inexpensive part, but the gearbox uses it to choose its gears: when it loses this information, it goes into safe mode.

New speed sensor for a Renault Quickshift automated gearbox
The speed sensor: a 3-pin Hall-effect sensor clipped into the gearbox at the differential.

Which vehicles are concerned?

This sensor is fitted to petrol Quickshift models:

  • Twingo 1 (2001-2007) and Twingo 2 (2007-2014)
  • Clio 2 (2001-2007) and Clio 3 1.2 (2005-2014)
  • Modus 1.2 (2005-2012) and Grand Modus 1.2 (2008-2012)

Manufacturer references: 7700418919 and 7700840042.

Symptoms of a faulty speed sensor

  • The speedometer drops to 0 or goes haywire while driving, then comes back.
  • The "A" disappears: the gearbox leaves automatic mode and switches to manual mode.
  • The gearbox drops back into neutral while driving or when coming to a stop.
  • Inconsistent gear changes: the gearbox no longer knows how fast the car is going.
  • Intermittent symptoms that come and go, often after driving on a wet road or over bumps.

The most reliable clue is the speedometer: it uses the same information. A speedometer that falls to 0 just as the gearbox loses mode A almost certainly points to the sensor or its wiring.

Related fault codes

  • DF048 on the Renault CLIP tool: vehicle speed information.
  • P0720 (DTC0720): the same fault read in P-code format.
  • P0500 on a generic diagnostic tool: vehicle speed sensor fault.

→ The complete list of Quickshift fault codes

Speed sensor or pressure problem?

Both make the "A" disappear. To tell them apart:

Speed sensor Pressure (accumulator, electric pump)
Speedometer Drops to 0 or goes haywire Normal
Electric pump Works normally Starts at every gear change
Codes DF048 / P0720 / P0500 DF078, DF257, DF258

→ Diagnosing a pressure problem (code DF078)

Checking the sensor and its wiring

  1. Locate the sensor: it sits on the gearbox, bulkhead side (between the engine and the bulkhead), at the differential output. It is in the same place as on the JB1/JH1 manual gearbox. It is simply clipped in (no screw) and is reached from underneath the vehicle. It has a 3-pin connector.
  2. Check the connector: fully pushed in, locked, with no corrosion and no spread pins. Clean it with contact cleaner.
  3. Follow the cable to the wiring harness: a chafed, pinched or cut wire gives exactly the same symptoms.
  4. Clear the codes, then take a road test. If the fault comes back and the wiring is fine, replace the sensor.

Replacing the speed sensor

The replacement does not open the robot's hydraulic circuit: no need to release the pressure, no bleeding and no relearning.

  1. Switch the ignition off and disconnect the battery.
  2. Clean around the sensor so that no dirt falls into the gearbox.
  3. Unplug the connector by pressing its locking tab, without pulling on the wires.
  4. Unclip the old sensor from underneath: pass a long flat screwdriver through the torque rod (the lower engine mount, fixed under the gearbox), rest the tip of the screwdriver under the sensor and give it a sharp tap: the sensor unclips upwards. Take it out from above.
  5. Fit the new sensor: line it up straight in its housing, seal lightly oiled, and press on it until it clips in.
  6. Plug the connector back in until it clicks, reconnect the battery.
  7. Clear the codes with the diagnostic tool and take a road test: the speedometer should work and mode A should hold.

Avoid used parts: a scrapyard sensor is as old and as worn as yours. A new sensor costs little and fixes the problem for good.

→ SPECIAL Quickshift speed sensor (new part)

FAQ

The speedometer works but I still lose the A: is it the sensor?

Rarely. If the speedometer stays normal, look for a pressure or gear lever problem instead. → Diagnosing the Quickshift gearbox

Do I need a diagnostic tool to replace the sensor?

Not for the replacement. The tool is only used to read and clear fault codes.

Does this sensor fit a diesel Clio 3 or Modus?

No, this sensor is for the petrol versions listed above. For a diesel, contact us with your registration number.


Not sure about your symptom? Write to us in the chat at the bottom right with your fault codes: we will tell you the right part for your vehicle.

← Back to the Diagnosis blog

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.