Quickshift electric pump fuse keeps blowing: causes and solutions

Quickshift electric pump fuse keeps blowing: causes and solutions

Does your Quickshift electric pump fuse blow as soon as you switch on the ignition, or after a few minutes of driving? Without it, the pump stops, pressure drops and the gearbox stays stuck in neutral or in the engaged gear. A new fuse fixes nothing if the cause is still there: a blowing fuse means either a short circuit or excessive current draw by the electric pump. Here is how to tell them apart and find the faulty part.

Safety: never replace this fuse with a higher rating and never bridge it. You could melt the wiring or burn out the electric pump. Always fit the rating shown on the fuse box cover (often 30 A).

Where is the fuse?

The electric pump fuse is in the engine compartment fuse box. On the Twingo 1, the workshop manual gives it as position no. 9. On other models, find it using the diagram printed under the cover or in the owner's manual. Remove it and look at the filament: if it is broken or blackened, it has blown.

1. The fuse blows immediately with the ignition on: a short circuit

If the fuse blows the moment the pump should start, or even without the pump running, the current is finding a direct path to earth. Do this test:

  1. Unplug the electric pump connector.
  2. Fit a new fuse of the correct rating, then switch on the ignition.
  3. The fuse holds: the short is on the electric pump side (motor or pump connector).
  4. The fuse blows again: the short is in the wiring or at the relay. Inspect the wires along the gearbox, especially where they rub or run close to the exhaust.

A real case worth knowing on the Twingo: a sensor under the gearbox that was badly clipped in, with a broken plug, blew the fuse every time. So also check the sensor connectors under the gearbox, including the speed sensor. → Quickshift speed sensor

2. The fuse blows after a while: the pump draws too much current

If the car drives for a while before the fuse goes, the electric pump is drawing too much current. Three causes come up:

The pump is dragging or jammed

When an accumulator bursts internally, debris gets into the oil. It slows down or jams the gear pump: the electric motor strains and the fuse blows. In this case, replacing the fuse or even the electric pump alone is not enough: replace the accumulator and the electric pump, drain the reservoir and change the hydraulic block filter.

Renault Quickshift robot electric pump
An electric pump slowed by debris strains and blows its fuse.

Location of the Quickshift hydraulic block filter at the electric pump outlet
After a burst accumulator, the hydraulic block filter is often clogged: replace it.

→ Repair kit (accumulator + electric pump + oil) · Oil change kit (filter + oil)

The pump runs without ever stopping

Normally, the electric pump runs for a few seconds, fills the accumulator, then stops. If it no longer stops, it overheats and ends up blowing its fuse. Two origins:

  • Pressure is never reached: worn accumulator, oil level too low, a leak or a clogged filter. → Robot oil leaks
  • The pump relay is stuck closed: the pump keeps running even with the ignition off. If you can still hear it after removing the key, replace the relay with an identical new one.

The electric pump is worn

An electric pump at the end of its life, which has long run continuously behind a tired accumulator, draws more current and ends up blowing the fuse. Replace it together with the accumulator: they wear at the same rate. → Accumulator replacement guide

Renault Quickshift gearbox pressure accumulator
A tired accumulator makes the electric pump run continuously and wears it out early.

Summary

What you notice Likely cause Solution
Blows with the ignition on, even with the pump unplugged Short circuit in the wiring or relay Inspect and repair the wiring, replace the relay
Blows with the ignition on, holds with the pump unplugged Electric pump or its connector Check the connector, replace the electric pump
Blows after a few minutes Pump slowed by accumulator debris Accumulator + electric pump + oil change + filter
The pump runs without stopping Pressure never reached Accumulator, oil level, leaks, filter
The pump runs with the ignition off Pump relay stuck closed Identical new relay

FAQ

Can I drive while waiting for the repair?

No. Without the electric pump there is no pressure: the gearbox stops changing gear and locks up. If it is stuck in gear, the car is moved on a flatbed. → Unlock and tow a Quickshift

I replaced the electric pump and the fuse still blows

Then the short is in the wiring or at the relay, or the new pump is being slowed by debris left in the circuit. Do the pump-unplugged test, then drain and change the filter if the accumulator had burst.

The fuse holds, but the pump still does not run

Check the relay, the electric pump connector, the earth and the battery voltage. → Parts replaced but the gearbox still does not work

→ Pump running non-stop or restarting too often: relay, priming, accumulator or leak?


Still stuck? Message us in the chat at the bottom right with the model, year and your fault codes: we will help you find the faulty part.

← Back to the Diagnosis blog

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.