Accumulator and electric pump replaced, the Quickshift still won't work: what to check?

Accumulator and electric pump replaced, the Quickshift still won't work: what to check?

You have replaced the accumulator and the electric pump, but the Quickshift gearbox still won't start, stays in neutral or still shows a fault code? In most cases the new parts are not to blame: a fitting detail or another part of the circuit is preventing the system from coming back to life. Here are the checks to make, in order, before you take anything apart.

Reminder: replacing the accumulator and the electric pump requires no bleeding and no relearning. If the gearbox does not come back, it is not a forgotten bleed.

New accumulator and electric pump for a Renault Quickshift gearbox robot
Accumulator and electric pump: the pressure circuit of the Quickshift robot.

1. Listen to the electric pump with the ignition on

With the bonnet open, switch the ignition on without starting the engine. The electric pump should run for a few seconds, then stop: it fills the accumulator up to about 50 bar and restarts at around 40 bar. Its behaviour points the whole diagnosis in the right direction:

  • It does not run at all: the problem is electrical (see step 2). A new electric pump that stays silent is almost always not getting power, not faulty.
  • It runs and never stops: the pressure is not building up. Check the oil level, the connections and the filter (steps 3 and 4).
  • It runs, then stops normally: the pressure is good. Look at the gear lever, the brake sensor or stored codes (steps 5 and 6).

2. The pump does not run: fuse, relay and connectors

  1. The electric pump fuse: check it and replace it if it has blown. If it blows again straight away, look for a short circuit or a seized pump.
  2. The pump relay: a tired relay sticks or no longer switches. It often shows up as fault codes DF065 or DF252 (pump relay circuit). Replace it with an identical new relay.
  3. The electric pump connector: make sure it is fully pushed in and locked, and that its pins are neither corroded nor spread apart. A shot of contact cleaner in the robot and ECU connectors fixes many poor contacts.
  4. Earth and battery: a weak battery stops the pump from building up pressure. Check the voltage (12.4 V minimum with the engine off).

New electric pump for a Renault Quickshift robot with its connector
A new electric pump that does not run is almost always a power supply issue: fuse, relay or connector.

3. The pump runs without stopping: oil level and air intake

If the reservoir emptied during fitting, the pump draws in air and cannot build up pressure.

  1. Set the level with no pressure in the circuit: between 34 and 38 mm above the reservoir joint line, with robot oil.
  2. Prime the pump: switch the ignition on for a few seconds, switch off, check the level and top up. Repeat until the pump stops by itself.
  3. Check for leaks: accumulator properly tightened with its seal, electric pump connections tight, no trace of oil around the hydraulic block.

Quickshift robot oil level with no pressure: 34 to 38 mm above the reservoir joint line
With no pressure, the level must be between 34 and 38 mm above the reservoir joint line.

→ The complete guide to oil level and oil change

The pump runs non-stop and the reservoir level does not drop? It has not primed and is running dry. Remove it again and fill it with robot oil before refitting it, or, without removing anything, use a syringe to draw out the air bubble at the bottom of the reservoir. → Electric pump running constantly

4. Pressure builds up poorly: filter and pressure sensor

The hydraulic block filter, at the electric pump outlet, is the most often forgotten part. When the old accumulator failed, debris may have circulated and clogged this filter: the pump strains, the pressure builds up slowly and the gearbox drops into neutral. If the oil is black or dirty, change the oil and the filter.

Location of the Quickshift hydraulic block filter at the electric pump outlet
The filter sits behind the electric pump outlet union, on the hydraulic block.

The pressure sensor tells the ECU the circuit pressure. If it is faulty, the ECU thinks pressure is missing even with new parts. Related codes: DF005 or DF166 (pressure sensor circuit), sometimes a persistent DF078. On the diagnostic tool, an inconsistent pressure reading (0 bar while the pump runs and stops normally) points to the sensor.

→ Oil change kit (filter + oil) · Pressure sensor

5. The pressure is good but the car won't start

If the pump runs and then stops normally, the hydraulic circuit is working. The no-start then comes from elsewhere:

  • The gear lever: if it does not send the "neutral" signal, the ECU blocks starting. Do the test: unplug the lever connector and start the car. If it starts, the lever is at fault (code DF067 is common). → Diagnosing the gear lever
  • The brake pedal sensor: the gearbox requires your foot on the brake to start and engage 1st gear. If the sensor does not detect the pedal, nothing happens. → Brake sensor

6. The fault code is still displayed

A stored code does not disappear by itself after the repair. Clear the codes with the diagnostic tool, switch the ignition off for 15 seconds, then run a new diagnosis:

  • The code does not come back: it was a stored code from the old fault, the repair is good.
  • The code comes back straight away: the cause is still there. Go back through the list above and check the complete list of Quickshift fault codes.

Summary

What you notice Check first
The pump does not run with the ignition on Fuse, pump relay, connector, battery
The pump runs without stopping Oil level, priming, tightness of the accumulator and unions
Pressure builds up slowly, drops into neutral Hydraulic block filter, worn oil
Pressure reads 0 although the pump stops Pressure sensor
The pump stops normally but no start Gear lever, brake sensor
The code stays displayed Clear the codes, then run a new diagnosis

FAQ

Do I need to release the pressure before removing the accumulator?

Yes: with the diagnostic tool, or by leaving the vehicle to rest for 48 to 72 hours with the electric pump unplugged. To loosen a seized accumulator, use a suitable fitting wrench. → Accumulator guide

Does the pressure come back by itself after refitting?

Yes. The first time you switch the ignition on, the electric pump fills the accumulator. No action with the diagnostic tool is needed.

Why replace the accumulator and the electric pump together?

They wear at the same rate. A tired accumulator makes the pump run constantly and wears it out; a worn pump will not last with a new accumulator. → Repair kit (accumulator + electric pump + oil)


Still stuck? Write to us in the chat at the bottom right with your fault codes: we will help you find the faulty part.

← Back to the Diagnosis blog

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.