Quickshift robot oil leaks: overfilled reservoir, cap, hoses, seals
Share
Is your Quickshift robot reservoir emptying, with oil on the robot or drips under the car? A leak lowers the oil supply: the electric pump draws in air, pressure drops and the gearbox ends up dropping into neutral or showing a fault code. Before replacing parts, make sure it really is a leak: an overfilled reservoir overflows and leaves exactly the same traces. Here are the points to check, from the simplest to the longest.
Reminder: the reservoir level varies with pressure. Without pressure, it must be 34 to 38 mm above the reservoir joint line. With the circuit under pressure, some of the oil is stored in the accumulator and the level drops towards the joint line: this is normal.

Without pressure, the level must be 34 to 38 mm above the reservoir joint line.
1. An overfilled reservoir overflows
This is the most common false leak. If you top up the reservoir to the "no pressure" level while the circuit is still under pressure, there is too much oil. When the pressure drops, the oil stored in the accumulator returns to the reservoir, which overflows through the cap. The result: oil on the robot, sometimes drips on the ground, and the impression of a leak.
- Release the pressure: with a diagnostic tool, or by leaving the vehicle at rest for 48 to 72 hours with the electric pump unplugged.
- Check the level without pressure: it must be 34 to 38 mm above the joint line.
- Remove the excess with a syringe if it is too high.
- Clean the robot with degreaser and check again a few days later: if nothing reappears, there was no leak.
Never add oil just after driving without taking the pressure into account. → The complete oil level and oil change guide
2. Finding the source of a real leak
Thoroughly clean the robot, the reservoir and the underside of the gearbox, then switch the ignition on several times and drive a few kilometres. The place where oil reappears first, often the highest point of the trace, is the source of the leak. Use only robot oil for topping up.
The reservoir cap and its seal
A cracked or loose cap, or one with a hardened seal, lets oil seep out, especially when the reservoir is full. Replacement is immediate. → Reservoir cap + seal

Reservoir cap and seal: the simplest leak cause to rule out.
The reservoir, its seals and its hoses
Check the base of the reservoir, its seals on the hydraulic block and the hoses connecting the reservoir to the pump. On some diesels, the rigid plastic reservoir hose cracks with age. The lower hose and its fittings can also leak if they were not retightened properly after a repair.
The accumulator and electric pump fittings
After a replacement, an accumulator that is not tightened properly or is missing its seal, or a loose electric pump fitting, leaks under pressure. Retighten to the correct torque with a suitable fitting wrench. → Accumulator guide
The disc at the back of the robot
A disc that has popped out or seeps at the back of the robot lets oil escape. It is replaced with its seal and circlip. → Disc + seal + circlip

Disc, seal and circlip: check them if oil leaks at the back of the robot.
The cylinder seals
The robot cylinders (clutch, selection, engagement) are sealed by seals. Worn or split, they let oil leak outside or pass into the selection housing: the gearbox then loses its gears and the reservoir empties with no visible trace. On the Clio 3, Modus, Trafic and Master, the clutch cylinder can be rebuilt with a seal kit. → Clutch cylinder seal kit
The seal between the robot and the gearbox
An oil trace between the robot and the gearbox casing comes from the seal fitted between them. If the reservoir level drops at the same time, it is indeed robot oil escaping. → Robot / gearbox seal

The seal between the robot and the gearbox.
A leak through a sensor or connector
Oil can creep up through a position sensor or seep into a robot connector. A connector full of oil causes poor contacts and fault codes. Clean it with contact cleaner and replace the sensor if it leaks.
Reservoir emptying with no trace at all
If the level drops without any external trace, the oil is passing inside the robot, most often through a cylinder seal. Do not just top up: the pump will end up drawing in air and the pressure will drop (code DF078 is common). → Fault code DF078
Summary
| Where the oil is | Likely cause |
|---|---|
| Around the cap, after a top-up | Overfilled reservoir overflowing |
| Around the cap, correct level | Cap or cap seal |
| Base of the reservoir, hoses | Reservoir seals, cracked hose, loose fitting |
| Around the accumulator or electric pump | Tightening or seal after replacement |
| Back of the robot | Disc popped out or seeping |
| Between the robot and the gearbox | Robot / gearbox seal |
| In a connector or around a sensor | Leak through the sensor |
| No trace, level dropping | Internal cylinder seal |
FAQ
Can I drive with a small leak?
For a few days while monitoring the level without pressure, yes, but a leak only gets worse. A reservoir that is too low makes the electric pump run non-stop, which wears it and can blow its fuse. → The electric pump fuse keeps blowing
The level has dropped after driving: should I top up?
No. With the circuit under pressure, the level drops towards the reservoir joint line: this is normal. Only the measurement without pressure counts; topping up at that moment makes the reservoir overflow later.
Should the oil be changed after a leak?
If the oil is black or the reservoir emptied far enough for the pump to draw in air, yes: change the oil and the filter. → Oil change kit (filter + oil)
Can't find where the leak comes from? Send us a photo in the chat at the bottom right: we will help you identify the part.